Authorized BÖWE, LG, OASIS & Sankosha distributor · Serving Canada since 1993
Extox Blog

Hydrocarbon Dry Cleaning Solvent: Safety and Handling Guide

Hydrocarbon solvent has become the go-to PERC alternative for many Canadian dry cleaners. It is gentle on garments and easier on the regulatory side. But it is a combustible liquid, and it needs to be stored and handled with that in mind. This guide covers the practical safety basics every plant using hydrocarbon should have in place.

We use DF-2000, a widely used isoparaffinic hydrocarbon dry cleaning fluid, as the example below. Figures come from the manufacturer’s safety data sheet (SDS). Always keep the current SDS for the exact product you buy on site, and check it when anything changes.

>61°CFlash point (DF-2000, ASTM D-93)
Category 4Flammable liquid: “combustible liquid”
AspirationCan be fatal if swallowed and it enters the airways

Why hydrocarbon needs different habits than PERC

Staff who learned on PERC sometimes treat every solvent the same way. That is risky. PERC does not burn under normal conditions. Hydrocarbon does. Its flash point is high enough that it is classed as combustible rather than flammable, but vapours can still ignite if the liquid is heated, sprayed or spilled near a source of ignition. Modern hydrocarbon machines are designed with this in mind, which is why it matters to keep them maintained and never bypass their safety features.

Storage: the five rules we tell every customer

  1. Keep containers closed. Open drums only when you are filling or transferring, and open them slowly to release any pressure.
  2. Store cool and ventilated. Keep drums away from boilers, dryers, presses, heaters and direct sunlight.
  3. Ground and bond. The SDS notes that this fluid can build up static electricity. Ground storage containers and fixed equipment, and bond containers during transfers.
  4. No ignition sources nearby. No smoking, open flames or sparking tools in the storage area.
  5. Use compatible materials. Stainless steel, carbon steel and Teflon are listed as suitable. Natural rubber, butyl rubber, EPDM and vinyl coatings are not. Check gaskets and hoses when you replace them.

Handling and transfers

Most incidents happen during transfers, not while the solvent sits in the machine. A few habits make a big difference:

  • Use a proper closed transfer system or pump rather than pouring.
  • Bond the drum and the receiving container before you start.
  • Clean up small drips right away. Spilled solvent is also a slip hazard.
  • Never transfer near a running boiler, open flame or hot equipment.

Ventilation and exposure

Breathing high concentrations of hydrocarbon vapour can cause headaches, dizziness and drowsiness. Good general ventilation keeps exposure low, and the manufacturer recommends explosion-proof ventilation equipment where vapours may collect. If you ever notice a solvent smell in the plant, treat it as a sign that something needs attention: a door seal, a filter, a leak or a maintenance issue.

Personal protective equipment

  • Gloves: chemical-resistant gloves for any prolonged or repeated contact, such as filter changes and still cleaning.
  • Eyes: safety glasses with side shields when splashing is possible.
  • Clothing: chemical and oil resistant clothing for messy maintenance jobs.
  • Hygiene: wash hands before eating, drinking or smoking.

Hydrocarbon can dry out the skin with repeated contact, so gloves are worth insisting on even for “quick” jobs.

First aid: the one thing to remember

If someone swallows hydrocarbon solvent, do not induce vomiting. The main danger is the liquid getting into the lungs, which can cause serious lung damage. Get medical help immediately. For skin contact, wash with soap and water. For eyes, flush with water. Post the first aid section of your SDS where staff can see it.

If there is a spill

  • Shut off ignition sources first.
  • Stop the leak if you can do it safely.
  • Keep the spill out of floor drains and sewers.
  • Absorb it with sand, dry earth or a non-combustible absorbent, using non-sparking tools.
  • Dispose of the used absorbent as solvent waste.

Keep a spill kit next to the machine and the drum storage, and make sure everyone knows where it is.

If there is a fire

Use water fog, foam, dry chemical or carbon dioxide extinguishers. Do not use a straight stream of water, which can spread burning solvent. Make sure the extinguishers near your machine are rated for this kind of fire and inspected on schedule.

Waste and still bottoms

Used filters, still residue and contaminated absorbents still contain solvent and must be handled as waste, not thrown in the garbage. Keep them in closed, labelled containers and arrange regular pickup by a licensed carrier. If you are switching from PERC, keep the two waste streams separate.

A simple monthly checklist

  • Current SDS on file and accessible to staff
  • Drums closed, labelled, grounded and away from heat
  • Spill kit stocked
  • Extinguishers inspected
  • Machine door seals and gaskets checked
  • Waste containers closed and pickup scheduled

Frequently asked questions

Is hydrocarbon safer than PERC?

They have different risks. Hydrocarbon is far less regulated than PERC and is generally considered gentler on people and garments, but it is combustible, so fire safety becomes the focus. Our solvent comparison covers the trade-offs.

Can I use hydrocarbon in my old PERC machine?

No. Hydrocarbon must be used in a machine designed for it, such as a multi-solvent machine. Using it in a PERC machine is unsafe.

Where can I buy DF-2000?

Extox supplies DF-2000 hydrocarbon solvent across Canada, along with filters and spotting agents that work with it.

Switching to hydrocarbon?

We can help with the machine, the solvent, safe storage and waste pickup. Talk to our team about your plant.

Talk to a specialist

Questions about your plant?

Talk to an Extox specialist about equipment, chemistry or compliance.

Request a Quote

Leave a Reply

Your email address will not be published. Required fields are marked *

Call Request a Quote